DJR Full Body V2 Heatsink
	Introducing the "next generation" Dorcy Jr Heatsink.  The new design provides additional mass and also allows/requires the use of an "after-market" diode-driver such as "Dr. Lava's" Flexdrive, as the additional length requires the removal of all of the original "guts" from the host.   These are precision-machined on all surfaces from "billet" 6061-T6 "aircraft-grade" aluminum, plus the added feature of being anodized with area's "masked" to retain the ground-condutivity from the host.  Still has #6 set screws and slids right in. These now also include a replacment O-ring which is thicker and works better for this mod.   Total weight for this heatsink: 17.3 grams of aircraft-grade aluminum.     Check the "kits-page" I stock a few host/heatsink/battery/ module packages available for your convience.   Dark Horse Custom Inc does not sell laser-devices or electronics. You will have to aquire your own diode and driver to complete a build to your design, laser or otherwise.	$22.00 each S/H Incl.

Sliver Full Body Heatsinks
	Introducing The "Sliver" Full Body Heatsink.   Based on the successfull "Full-Body" design used in the Dorcys, these are down-sized for a Cree C3 (solid stainless-steel 1xAA-sized host) This new design fits in a smaller host (21mmx 94mm). You will need a 14500 (AA-sized) lithium-battery for this little guy, I recommend these from DX.     Check the "kits-page" I stock a few host/heatsink/battery/module packages available for your convience.   Dark Horse Custom Inc does not sell laser-devices or electronics. You will have to aquire your own diode and driver to complete a build to your design, laser or otherwise.	$20.00 each S/H Incl.

DJR Heatsink - Blk Anodized
	The original aluminum heat-sinks for use in the Dorcy Jr modification. These are precision-machined on all surfaces from "billet" 6061-T6 "aircraft-grade" aluminum, and anodized black. The outside diameter fits closely inside of the head of the Dorcy Jr host and is stopped by the small o-ring that originally sealed the plastic lens, ( a thicker replacement O-ring id provided and works even better). The inner-diameter Of the 'sink is a "slip-fit" for a LD-module, such as Aixiz, Sure and DX. The length is 3/8" (9.5mm).  There are two #6 set-screws that are tapped through the diameter to positively hold your module in place and provide good surface contact for thermal transfer, (a small amount of thermal-compound, such as Arctic-Silver may be applied to the outside of your module to further increase heat-transfer). A very small wrench is also included for these very small screws, (Dr Seuss?). Total weight for this heatsink: 5.5 grams of aircraft-grade aluminum.   Dark Horse Custom Inc does not sell laser-devices or electronics. You will have to aquire your own diode and driver to complete a build to your design, laser or otherwise.	$15.00 each S/H Incl.

*New!* ES Pen-'sink
Black Clear	Introducing the “ES” Pen- ‘Sink This nice little ‘sink  adds much needed heatsinking to your pen-style laser, increasing your duty-cycle and reducing any mode-hoping issue that are caused by excessive-heat. These accessories  also provide additional protection for your laser’s optics by way of the deeper aperture-hole, and adding more than a bit of style to these smallest of power-house laser-systems. We have test-fit these with Leadlight, CNI, and DX pen-lasers, they fit nearly all of them without damage to the warning-label. These are made to simply slide-over the aperture-end of you laser pointer and lightly tighten the provided set-screw. These heatsinks add 19.6 g of aircraft grade alumiun around your diode module. **Please note, we tried to make these large-enough to allow sliding over the warning-label present on most lasers of this style, but damage to your label  or even the laser’s finish can occur, especially with the CNI gloss-black finish, this finish is not very durable. We have tried very hard to make a product that can be used with confidence, but please do not force it on, we can make a larger size for you if needed.  We cannot be responsible for damage to your laser-unit. We are stocking these in: “Gloss-Black”, “Clear” and several custom finishes, check the catalog or contact us for current special-edition finishes that may be available. Read about it here: http://www.laserpointerforums.com/forums/YaBB.pl?num=1235786742/0#0 Dark Horse Custom Inc does not sell laser-devices or electronics. You will have to aquire your own diode and driver to complete a build to your design, laser or otherwise.	$25.00 each S/H Incl. Colors Black Clear BlackClear

DJR Heatsink - Limited Edition (Blk over Violet)
	Same as the "The Original DJR Heatsink" with a Black over Violet custom anodize job. Dark Horse Custom Inc does not sell laser-devices or electronics. You will have to aquire your own diode and driver to complete a build to your design, laser or otherwise.	$17.00 each S/H Incl.   Limited Availablity