I loosely bolted the propulsion unit to the rear wheel of my Cannondale T-400 touring bike and tried to install it on the frame. All the frame tubes are larger, being aluminum. So the propulsion unit went against the chainstays. I ground a couple of notches into the propulsion unit to make clearence. It still touches the chainstays and I hope it won't be a problem. The hose clamp for the torque arm barely made it aroung the fat chainstay.

I mounted the throttle upside down on the top of my drop handlebars. I used some black duct tape to cover the openings. I work the throttle by pulling it up with my index and middle finger. It's quite comfortable.

The battery mounting scheme wouldn't fit in the frame triangle, again because of the fat frame tubes. So I opened up the battery box and removed the tab for fastening with the key and strapped the front of the battery box to the top tube with a long hose clamp. The seat tube bracket works OK.

During all of this I charged the batteries with the supplied charger. They sent me two chargers, by mistake I assume. These chargers are labeled 2 amps and seem to be pretty smart. When the battery reached 30V it switched to float mode at 27.3V. The charger is 3x6x12 cm and light. It's a switching supply and caused some TV interference next to a TV with rabbit ears. The first charge took 3 hours.

Yesterday evening I excitedly took the bike out for a spin around my neighborhood. The acceleration was a little startling at first and it was quieter than I thought it would be, a whirring that gets quieter up to speed. The weight distribution is good, it doesn't seem to adversly affect the handling. I weigh 145lbs BTW. I haven't weight the bike with the kit on but it's tolerable carrying it up one flight of stairs. I increased the air in my (32mm) Conti. Top Touring tires 5 lb to 65psi front, 75psi rear.

This morning I rode to work, about 1.5 miles. I don't NEED the assist for this commute but it sure is fun. I work in a college electrical engineering dept. so I spent most of the morning letting co-workers take rides. It was quite a sensation. The battery recharged in 2 hours.

I cut a 5x8" piece of 1/16" aluminum sheet and cut the holes for it to fit between the motor and propulsion unit, ala Jay Ward, and mounted it with thermal grease.

Then I went downtown (Wash. DC) to run some errands and show the kit to the folks at the bike shop I frequent. The whole trip was about 5 miles. There were some moderate hills, gridlock traffic, and 95 degree sunny weather. The system worked flawlessly. No manic couriers whizzing by me up hills. I didn't break a sweat until I got off the bike, no more breeze.

Today I fully opened the battery box. Boy, did they pack it in! I tightened the connectors and also soldered the crimps on the battery and switch connectors. Of course I disconnected each lug from the battery before I soldered. The indicator light is an LED and draws only 10mA so it get a reprieve. I recall reading somewhere it drew more current.

I couldn't find a place to flush mount my little LCD voltage display so I strapped it outside on the carrying handle.

I added another wire to the 3 pin charging connector, leading to the middle battery connector. Now I can measure or charge the two batteries individually. This [XLR] connector is originally for microphones, readily available.

I also finished building a charger that will charge the batteries individually. I'll use that periodically to make sure both batteries get fully charged. The batteries are Portalac Model PE12V12 made by Japan Storage Co. They measure 3 7/8 X 3 11/16 X 5 15/16.

I did a little more grinding on the propulsion unit and added a washer between the frame and rear axle so there is definate clearence between the propulsion unit and frame tubes.

The foam rubber where the torque arm clamps to the chain stay wore away so I put a piece of much tougher neoprene there.

The chain tensioner got noisy so I replaced it with one of Scott McGregor's replacement blocks. Much better. Great job Scott! That chain seems to stretch alot. I've had to adjust every 20 miles or so. I tried to remove a pair of links - no way. I'll eventually have to get a half link from Scott.