Baker Electronix

Our Products

Module	Description	Pricing
RWS  (RPM Window Switch) ARWS (Adjustable RWS)	The RWS/ARWS module activates its output durring a window of RPMs, above a low RPM threshold and below a high RPM threshold.  More Information/Purchase Click Here for the RWS PDF Click Here for the ARWS PDF	$40 each $37 each at quantity five $35 each at quantity ten   For the adjustable (ARWS) module, with eight settings, just add $10.
TSD (Tachometer Signal Divider/Adaptor) ATSD (Adjustable TSD)	The TSD/ATSD module is essential for anyone installing a new engine in a vehicle that is equip with a stock tachometer designed for a differnt number of cylinders. More information/Purchase Click Here for the TSD/ATSD PDF	TSD $40 each $37 each at quantity five $35 each at quantity ten   The ATSD (Adjustable-TSD) is $10 more
TSI (Tachometer Signal Inverter)	The TSI module is essential for anyone needing to convert a coil-type engine speed signal to an inverted, and lowerd voltage, signal for use ECM and other computers, where no frequency multiplication is needed. More information/Purchase	$40 each $37 each at quantity five $35 each at quantity ten
DDFC (DeLorean Dual Fan Controller)	The DDFC module fixes the fan related problems commonly found with the DeLoreans.  These problems may include stalling at idle when the fans kick on and other electrical problems caused by brown out type conditions in the electrical system.   More Information/Purchase Click Here for the DDFC PDF	$99 each
VATS bypass ( Standard or 30Hz VATS bypass) (Dual Frequency VATS (DFVATS) for $10 extra)	VATS (Vehicle Anti-Theft System) bypass module for any GM vehicle made from 1986/7 to 2002 that uses the PASSkeyII type VATS, this includes all LT1s and F-body vehicles, many LS1s, made during those years.  More Information/Purchase VATS FAQ Page	$25 each $22 each at quantity five $20 each at quantity ten
PLRC (Pulse Latching Relay Controller)	The PLRC module latches it's output on or off based on momentary triggering pulse.  The trigging pulse can be ether positive (12V) or negative (grounding).  Once triggered the PLRC ether turns on or off it's output.  Great for turning things on with a momentary push of a button.   More Information/Purchase Click here for PLRC document	$35 each $32 each at quantity five $30 each at quantity ten
Dual-PLRC Dual-(Pulse Latching Relay Controller)	The Dual-PLRC is great for turning things on/off with a momentary push of a button.  Or make any relay into a latching relay. The module latches each of its outputs on (or off) based on momentary triggering pulse, or series of pulses.  The trigging pulse can be ether positive (12V) or negative (grounding), selected at time of purchase.      More Information/Purchase	$65 each $62 each at quantity five $60 each at quantity ten
ATD (Adjustable Time Delay)	The ATD module is a variable delay electronic switch that once triggered will wait a user selectable amount of time before activating, grounding, its output.  Great for NOS type applications. More Information/Purchase Click Here for the ATD PDF	$40 each $35 each at quantity five $30 each at quantity ten
TPS/ATPS (Throttle Position Switch / Adjustable-TPS)	Turns on any relay or electronic device by grounding its output wire based on the voltage comming from your stock, 0 to 5 Volt, Throttle Position Sensor. Click Here for the ATPS PDF	$40 each $35 each at quantity five $30 each at quantity ten $10 extra for the adjustable version
AFRC (Adjustable Fan Relay Controller)	Turns On Radiator Fan Relay based on the existing temperature sensor that the PCM/ECM is already using. More information Click Here for the AFRC PDF	$50 each $45 each at quantity five $40 each at quantity ten
O2 Sensor Simulators DualO2Sim PSO2Sim D5VO2Sim S5VO2Sim	Oxygen Sensor Simulators are used to eliminate/prevent the Check Engine Light from coming on when the catalytic converter(s) has been removed or gutted.  Typically for use on off-road and/or racing vehicles ONLY.	As of Oct 2007, We have discontinued all O2 Simulator Sales We have talked with a representative of the EPA who has expressed to us that, in practice, they take the position that there really isn’t any legal application for O2 simulators, even though their own written policies clearly state that there are legal applications (vehicles that can never be used on public streets, open tubular chassis, no reverse gears ect.).  We are therefore permanently removing ourselves from the O2 simulator business before the EPA changes their written laws to reflect their verbal position.  We wish to thank our previous O2 customers for their business and for only using our simulators for legal applications.
LIM (LS1/LT1 Interface Module)	Harness relay module for LS1/LT1 conversions. Includes onboard VATS bypass and multi-relay functions More information	$200 each $10 extra for sixth relay $20 extra for Tachometer signal divider Out of stock - NO ETA -

Back to Top

Baker Electronix GM VATS Bypass Module   The VATS bypass module is intended for use when installing a GM engine equipped with PASSkeyII type VATS (Vehicle Anti-Theft System) into a vehicle missing the BCM (Body Control Module) The bypass module generates the signal normally sent from the BCM to the PCM/ECM when the proper key is detected. Without this signal, the fuel injectors will not work. Normally it costs between $150 and $300 to have this feature deleted from the PCM. By using our module you will accomplish the same function for less and you won't have to ship your PCM/ECM to have it reprogrammed. This module will work for all PASSkeyII type engine computers made from 1986 to 2002. See our VATS FAQ page for a list of vehcles that used the PASSkeyII type VATS. PLEASE NOTE: Any GM vehicle made from 86 to 93 may or may not need the 30 Hz version of our VATS bypass. For engine computers made from 86 to 93 we highly recommend that you purchase, or upgrade too, our DFVATS bypass (Dual-Frequency VATS), which has both the standard VATS signal type as well as the 30 Hz signal type, all in one module. The VATS bypass module uses a simple three-wire interface (power, ground, signal). A quick disonnect connector upgrade is availible, so that the module can be easily remove to re-enable the factory anti-theft system and protect your car over night or at the car show. YOU CAN'T DO THAT IF YOU HAD YOUR VATS PROGRAMED OUT OF YOUR PCM/ECM. This module comes equipped with a status LED that indicates that it is functioning. Available LED colors are red █ , yellow █ , green █ , blue █ and  white █. If a color is not specified you will receive red █. Other Features include: Microcontroller based for reliability and accuracy Waterproof Reverse voltage protection in the event of incorrect power connections Short circuit protection on all outputs to 12V or ground Light weight (31g) Small package (5.4cm x 3.5 cm x 1.5cm) 12 Month Warranty Older 30 Hz version avalible apon request DFVATS upgrad for $10 more (The DFVATS has both the standard and 30 Hz singnals, all in one!)   If you live in the U.S. and you wish to purchase 4 or less modules, you can purchase via Credit Card or PayPal by using the buttons below.  Your order will ship to you via USPS Priority Mail.   If you live outside the U.S. or want to purchase 5 or more modules or would like a different shipping method, please email us (at info_bakerelectronix@verizon.net) for a quote. Please include the following in your email - your module selection, quantity and your full shipping address. For technical questions please email us at bakerelectronix@verizon.net. Purchase the VATS bypass module For $25 + S&H by clicking the button below LED Color RedGreenYellowBlueWhite VATS Signal Standard30 Hz Please note: If your vehicle (or engine's PCM/ECM) was made from 1986 to 1993 it may or may not need the 30 Hz version of our bypass module.  Unless you know which you need we recommend that you purchase the DFVATS module which has both the standard as well as the 30 Hz signal types. Options and Upgrades: Add The DFVATS Upgrade For $10 More Add The Quick Disconnect Upgrade For $10 More Add Translucent Color Box Option For $2 More Box Color Translucent RedTranslucent GreenTranslucent Blue

Back to Top

Baker Electronix DDFC (DeLorean Dual Fan Controller) This module is intended to fix the fan startup problems common with DeLoreans. These problems may include stalling at idle when the fans kick on and other electrical problems caused by brown out type conditions in the electrical system. Features of the DeLorean Dual fan module: Microcontroller based for reliability and accuracy Small size 3.3in x 2.2in x 1.4in so it can fit inside the DeLorean Relay Compartment This module supplies the fans with power directly from the battery (via the 10 AWG) so as to not cause a voltage drop (brown out) at your fuse box Only one wire to connect up, 10 AWG to battery, the rest is just plug in The DDFC turns on one fan at a time with a 3 second delay so the high start up currents of each fan don’t both ‘hit’ your electrical system at the same time Two green LED’s on the wire side of our module indicate when each fan output is commanded on for troubleshooting ease Uses two standard 30A Bosch type automotive relays for easy parts replacement Fan outputs include anti-spike diode to protect relays and reduce electrical noise Each fan output wire is individually fused with a ATM/Mini-ATC type 15A fuse 12-month warranty from date of purchase against manufacturer defects If you live in the U.S. and you wish to purchase only one DDFC module, you can purchase via Credit Card or PayPal by using the buttons below.  Your order will ship to you via USPS Priority Mail.   If you live outside the U.S. or want to purchase 2 or more modules or would like a different shipping method, please email us (at info_bakerelectronix@verizon.net) for a quote. Please include the following in your email - your module selection, quantity and your full shipping address. For technical questions please email us at bakerelectronix@verizon.net. Purchase the DDFC for $99 + S&H

Back to Top

Baker Electronix RWSr / ARWSr (RPM Window Switch / Adjustable-RWS)   The ARWSr/RWSr module is an electric switch that activates above your selected turn-on RPM, and can deactivate above a higher turn-off RPM.  The RPM range is called a window, or RPM window.  This module is perfect for applications like enabling/disabling your NOS (Nitrous Oxide System) injection, shift lights, Rev-limiter or turning on/off just about anything. The ARWSr/RWSr module works on the standard coil signal that most tachometers would use, without effecting your tachometer readout, as well as 0-5V engine speed signals that some newer vehicles use. The module’s output can ground 2.0A directly, or the output can be used to activate a relay to operate any required loads.  No expensive RPM plug in “pills” to buy, the RWSr comes preprogrammed to your needs.   When ordering the RWSr we will need to know what type of engine this will be used with (4 cylinder, 6, 8, 12, LS1, Vortec, 2-Stroke, Wankel, etcetera) and your RPM window selection (a lower Turn-On RPM and it can have an optional higher Turn-Off RPM).   When ordering the ARWSr you must specify what type of engine this will be used with (4 cylinder, 6, 8, 12, LS1, Vortec, 2-Stroke, Wankel, etcetera) and your 8 RPM window selections (each window must have a lower Turn-On RPM and can have an optional higher Turn-Off RPM).  After you receive your ARWSr module you can select from each of your 8 settings by adjusting its three switches.    The RWSr, and ARWSr, modules are Factory Re-Programmable; If you ever need new settings programmed into your module, just email us for a reprogramming quote and Return instructions.   Features: ·        Microcontroller based for reliability and accuracy ·         Reverse voltage protection in the event of incorrect power connections ·         Short circuit protection on all inputs and outputs to 12V or ground ·         Output can sink/ground 2.0A continuous to ground, up to a 3A surge ·         Waterproof ·         Low current (5 - 15mA) ·         Indicator LED to confirm operation and indicate mode ·         Works from 8V to 25V supply voltage ·         Light weight (31g) ·         Small package (5.4cm x 3.5 cm x 1.5cm) - Factory Re-Programmable ·         12 month warranty from date of purchase against manufacturer defects   If you live in the U.S. and you wish to purchase 4 or less modules, you can purchase via Credit Card or PayPal by using the buttons below.  Your order will ship to you via USPS Priority Mail.   If you live outside the U.S. or want to purchase 5 or more modules or would like a different shipping method, please email us (at info_bakerelectronix@verizon.net) for a quote. Please include the following in your email - your module selection, quantity and your full shipping address. For technical questions please email us at bakerelectronix@verizon.net. Purchase RWSr Simulator For $40 + S&H Options and Upgrades: Upgrade the RWSr to the ARWSr For $10 More Add The Quick Disconnect Upgrade For $10 More

Back to Top

Baker Electronix PLRCr Module (Pulse Latching Relay Controller)   The PLRCr is an electric switch (no mechanical contacts to wear out) that will activate and deactivate its output based on a short input trigger pulse, or series of pulses.    The PLRCr is great for push button applications and for using any standard relay as a latching relay.   For ease of installation, the trigger pulse can be ether a 12v pulse or a grounding pulse.  The triggering pulse time must AT LEAST 0.1 seconds long.  Longer or shorter pulse times are available upon request.  A dead time of 0.1 seconds is provided between triggering pulses to prevent false triggering, during this dead time additional pulses will be ignored until 0.1 seconds after last detected pulse.  Longer or shorter dead times are available upon request. The PLRC module’s output (when “On”) can ground 2.0A directly or the output can be used to activate a relay to supply loads of any power requirements.    The standard PLRCr turns “On” (or “Off”) it’s output after receiving one pulse, it will keep its output in this state (“On” or “Off”) until it receives another pulse.  Multi-Pulse versions of the PLRCr are also available.  The PLRCr module can be (programmed by us) to require two or more pulses within a certain amount of time (a time window) in order to change the module’s output status.  To order the multi-pulse version, please specify the number of pulses required (2 or more) and the time window (in seconds) that the PLRCr must receive these multiple pulses in.  The PLRCr will normally default to the output Off state when powered up (Default to Off), but other options are Default to On, and Default to last state.  When defaulting to last state, the PLRCr will remember whether its output was On or Off when it last powered down, it will turn back to On, or Off, the next time it is powered up.  You can request Default On or Default to last at the time of purchase. The PLRCr module is Factory Re-Programmable; If you ever need new settings programmed into your module, just email us for a reprogramming quote and Return instructions. Features: Microcontroller based for reliability and accuracy Reverse voltage protection in the event of incorrect power connections Short circuit protection on all inputs and outputs to 12V or ground Positive (12V) or Negative (Ground) type input trigger wires for ease of installation. Positive trigger voltage can be any voltage from 5V to 20V Output can sink/ground 2.0A continuous to ground, up to a 3A surge Waterproof Low standby current (5 - 15mA) Indicator LED to confirm operation and indicate mode Works from 8V to 25V supply voltage Light weight (31 g) Small package (5.4cm x 3.5 cm x 1.5cm) - Factory Re-Programmable 12 month warranty from date of purchase against manufacturer defects If you live in the U.S. and you wish to purchase 4 or less modules, you can purchase via Credit Card or PayPal by using the buttons below.  Your order will ship to you via USPS Priority Mail.   If you live outside the U.S. or want to purchase 5 or more modules or would like a different shipping method, please email us (at info_bakerelectronix@verizon.net) for a quote. Please include the following in your email - your module selection, quantity and your full shipping address. For technical questions please email us at bakerelectronix@verizon.net. Purchase the PLRCr for $35.00 + S&H LED Color RedGreenYellowBlueWhite Options and Upgrades: Add The Quick Disconnect Upgrade For $10 More

Back to Top

Baker Electronix Dual-PLRC Module Dual-(Pulse Latching Relay Controller)   The Dual-PLRC is an electric switch (no mechanical contacts to wear out) that will activate, and deactivate, its two outputs based on a short input trigger pulse, or series of pulses, to its two trigger wires.  It essentially has the function of two of our standard PLRC modules.  Perfect for applications where space and weight is limited.   The Dual-PLRC is great for push button applications and for turning any inexpensive relay into a latching relay.   For ease of installation, positive (12V) triggering or negative triggering (grounding) is available upon request.  Let us know at the time of purchase which option you want for each of the two inputs.  The triggering pulse time must AT LEAST 0.1 seconds long.  Longer or shorter pulse times are available upon request.  A dead time of 0.1 seconds is provided between triggering pulses to prevent false triggering, during this dead time additional pulses will be ignored until 0.1 seconds after last detected pulse.  Longer or shorter dead times are available upon request.   The Dual-PLRC module’s two outputs can be ether a grounding type (AKA low side switch), or it can supply 12v (AKA High side switch).  The gournding type of output can "sink" up to 2.0 Amps continuous, with up to a 3 Amps turn-on surge current.  The positive type of output can supply up to 1A continuous with a 3A turn-on surge   There are 16 possible configurations of the Dual-PLRC: Possible choices for input and output #1 (Positive trigger In, Negative Output) (Positive trigger In, Positive Output) (Negative trigger In, Negative Output) (Negative trigger In, Positive Output) And the same choices,as above, for input and output #2.    The standard Dual-PLRC turns “On” (or “Off”) it’s output after receiving one pulse, it will keep its output in this state (“On” or “Off”) until it receives another pulse.    Multi-Pulse Dual-PLRC versions of the PLRC are also available.  The Dual-PLRC module can be (programmed by us) to require two or more pulses within a certain amount of time (a time window) in order to change the module’s output status.  To order the multi-pulse version, please specify the number of pulses required (2 or more) and the time window (in seconds) that the Dual-PLRC must receive these multiple pulses in.  Features: Microcontroller based for reliability and accuracy Reverse voltage protection in the event of incorrect power connections Short circuit protection on all inputs and outputs to 12V or ground Positive (12V) or Negative (Ground) type input trigger wires for ease of installation. Positive trigger voltage can be any voltage from 5V to 20V Negatove type output can sink/ground 2.0A continuous to ground, up to a 3A surge Positive type output can supply 1.0A continuous, up to a 3A surge Waterproof Low standby current (5 - 15mA) Indicator LED to confirm operation and indicate mode Works from 8V to 25V supply voltage Light weight (32g) Small package (5.4cm x 3.5cm x 1.5cm) 12 month warranty from date of purchase against manufacturer defects If you live in the U.S. and you wish to purchase 4 or less modules, you can purchase via Credit Card or PayPal by using the buttons below.  Your order will ship to you via USPS Priority Mail.   If you live outside the U.S. or want to purchase 5 or more modules or would like a different shipping method, please email us (at info_bakerelectronix@verizon.net) for a quote. Please include the following in your email - your module selection, quantity and your full shipping address. For technical questions please email us at bakerelectronix@verizon.net. Purchase the PLRC for $65.00 + S&H Input/Output #1 (Positive trigger In, Negative Output)(Positive trigger In, Positive Output)(Negative trigger In, Negative Output)(Negative trigger In, Positive Output) Input/Output #2 (Positive trigger In, Negative Output)(Positive trigger In, Positive Output)(Negative trigger In, Negative Output)(Negative trigger In, Positive Output)

Back to Top

Baker Electronix TSD/ATSD (Tachometer Signal Divider)/(Adjustable-TSD) Also Known as the Tachometer Adaptor The ATSD module is essential for anyone who is installing an engine into a vehicle that was equiped with a tachometer designed for an engine with a different number of cylinder. The ATSD module divides, or multiplies, the tachometer signal's frequency.  The TSD/ATSD also converts the single to a standard 0V to 12V pulse to operate your original stock tachometer.  The ATSD comes with eight standard settings, that you can switch between.  Download the TSD/ATSD manual for more information. The non-adjustable (TSD module) only comes with one setting that you must specify when you order. Download the TSD/ATSD manual for more information.   Features: Microcontroller based for reliability and accuracy Waterproof Reverse voltage protection in the event of incorrect power connections Short circuit protection on all inputs and outputs to 12V or ground Operating voltage from 8V to 25V Light weight (31g) Small package (5.4 cm x 3.5 cm x 1.5 cm) 12-Month Warranty from date of purchase against manufacturer defects   If you live in the U.S. and you wish to purchase 4 or less modules, you can purchase via Credit Card or PayPal by using the buttons below.  Your order will ship to you via USPS Priority Mail.   If you live outside the U.S. or want to purchase 5 or more modules or would like a different shipping method, please email us (at info_bakerelectronix@verizon.net) for a quote. Please include the following in your email - your module selection, quantity and your full shipping address. For technical questions please email us at bakerelectronix@verizon.net. Purchase the TSDr for $40 + S&H LED Color Red Green Yellow Blue White Multiplier x1/4 Multiplier x1/3 Multiplier x1/2 Multiplier x2/3 Multiplier x3/4 Multiplier x1 Multiplier x4/3 Multiplier x3/2 Multiplier x2 Multiplier x3 Multiplier x4 Multiplier x6 Multiplier x8 Multiplier Purchase the ATSD for $50 + S&H LED Color RedGreenYellowBlueWhite Options and Upgrades: Add The Quick Disconnect Upgrade For $10 More

Back to Top

Baker Electronix TSI (Tachometer Signal Inverter)   The TSI module converts a standard 0 – 12v coil type tachometer signal into a 0 - 5v tachometer signal by inverting and reducing the input pulses.  This module provides no frequency adapting, if frequency adapting is needed the TSD or ATSD are also available. Features:       Reverse voltage protection in the event of incorrect power connections  Short circuit protection on all inputs and outputs to 12V or ground         Waterproof    Inverts signals from 0 Hz to 5,000 Hz (0 - 75,000 RPM with a V8)    Low current (5 - 15mA)    Indicator LED to confirm that module has power    Works from 8V to 25V supply voltage    Light weight (31g)    Small package (5.4cm x 3.5 cm x 1.5cm)   12 month warranty from date of purchase against manufacturer defects   If you live in the U.S. and you wish to purchase 4 or less modules, you can purchase via Credit Card or PayPal by using the buttons below.  Your order will ship to you via USPS Priority Mail.   If you live outside the U.S. or want to purchase 5 or more modules or would like a different shipping method, please email us (at info_bakerelectronix@verizon.net) for a quote. Please include the following in your email - your module selection, quantity and your full shipping address. For technical questions please email us at bakerelectronix@verizon.net. Purchase the TSI for $40 + S&H LED Color RedGreenYellowBlueWhite Options and Upgrades: Add The Quick Disconnect Upgrade For $10 More

Back to Top

Baker Electronix AFRCr (Adjustable Radiator Fan Relay Controller) Can be use with any 0-5V sensor signal.      The AFRCr module is intended to operate a Bosch type automotive relay by switching one side of the relay drive coil to ground, the other side of the coil connects to 12V.  The relay is triggered base on a user selected voltage threshold of any 0V to 5V sensor signal.  As an E-Fan relay controller our module snoops the voltage on the temperature sensor that the PCM/ECM is already using so no extra sensor is required. The temperature sensor can be the standard automotive type that decreases in resistance as temperature increases (NTC) or it can be the PTC type that increase with temperature.   Please specify NTC(standard) or PTC when ordering.   The vehicle must not change its measuring sensitivity (supply impedance) over the temperature range otherwise the voltage on the sensor will jump and the module will false trigger at some settings. This excludes the GM LS1, but a new LS1 module version is coming soon.      In the standard version, the three slide switches on the front of the module set the relay turn on voltage threshold starting at 4.9V and can be adjusted down to 0.1V (in seven 0.7v steps) with a 0.1V turn off hysteresis threshold to reduce relay and fan cycling.  The standard settings are (NTC,4.9V-0.1V, 0.1V hys).  For custom AFRCr modules please specify (NTC/PTC, User adjustble voltage range, turn off  hysteresis voltage).  If you are unsure of how to specify custom module setting just let us know. The module will flash the switch setting (0-7) on the LED to confirm your settings at power up and upon waking from sleep (only if the switch settings have been changed). During normal operation the module will flash its LED every five seconds, one flash if the fan relay should be off and two flashes if the fan relay should be on. Changes in fan status (on/off) or to new switch settings only take effect at the following wakeup period, which happens every five seconds. The AFRCr module is Factory Re-Programmable; If you ever need new settings programmed into your module, just email us for a reprogramming quote and Return instructions. Features: Microcontroller based for reliability and accuracy Reverse voltage protection in the event of incorrect power connections Low current (5 - 8mA) Output wire can sink up to 2A to ground (with up to a 3A turn-on surge) Indicator LED to confirm operation and indicate mode Light weight (31 g) Small package (5.4cm x 3.5cm x 1.5cm) - Factory Re-Programmable 12 month warranty from date of purchase against manufacturer defects

Back to Top

Baker Electronix ATDr (Adjustable Time Delay)   The ATDr module is an electric switch, no internal mechanical contacts to wear out, that can be triggered ether by a 12v signal or a grounding signal.  Once triggered the ATDr waits a pre-selected amount of time before activating its own output, the output will stay active for as long as ether one of the input triggers is active.  The ATDr's output is a grounding type output that can ground 2.0A directly or be used activate a relay to operate any required loads.  Delay time is set via a turn adjustment.   Perfect for NOS (Nitrous Oxide System) injection applications or any application needing a delay after being triggered. When ordering we will need to know the minimum and maximum delay times you need for your application.  Delays can be from a fraction of a second up to several minutes. The ATDr module is Factory Re-Programmable; If you ever need new settings programmed into your module, just email us for a reprogramming quote and Return instructions.     Features: ·        Microcontroller based for reliability and accuracy ·         Reverse voltage protection in the event of incorrect power connections ·         Short circuit protection on all inputs and outputs to 12V or ground ·          Positive (12V) or Negative (Ground) type input trigger wires for ease of installation. ·         Output can sink/ground 2.0A continuous to ground, up to a 3A surge ·         Waterproof ·         Low current (5 - 15mA) ·         Indicator LED to confirm operation and indicate mode ·         Works from 8V to 25V supply voltage ·         Light weight (31g) ·         Small package (5.4cm x 3.5cm x 1.5cm) - Factory Re-Programmable ·         12 month warranty from date of purchase against manufacturer defects   If you live in the U.S. and you wish to purchase 4 or less modules, you can purchase via Credit Card or PayPal by using the buttons below.  Your order will ship to you via USPS Priority Mail.   If you live outside the U.S. or want to purchase 5 or more modules or would like a different shipping method, please email us (at info_bakerelectronix@verizon.net) for a quote. Please include the following in your email - your module selection, quantity and your full shipping address. For technical questions please email us at bakerelectronix@verizon.net. Purchase the ATDr for $40.00 + S&H LED Color RedGreenYellowBlueWhite Options and Upgrades: Add The Quick Disconnect Upgrade For $10 More

Back to Top

Baker Electronix LIM or DT Controller    The LIM (LS1/LT1 Interface Module) is a compact interface intended to be used when rewiring the engine harness of the LS1/LT1 engine to be transplanted into your older sports car.  The LIM has all the relays normally needed when swapping engines all in one small box. Each relay is configured for the proper type of request signal (12V or ground) that the PCM/ECM sends out to activate them. The five relays that come standard are for the High Speed Fan, Low Speed Fan, Fuel Pump, Starter solenoid and A/C Compressor a sixth relay can be added for $10 extra.  Each relay has a fused output as well as a blown fuse LED indicator.   All relay inputs have a diode to prevent the voltage spike (flyback) that is generated by any relay from damaging your valuable PCM In addition to the relays this module generates the GM * VATS or PASSkeyII bypass signal. It also has onboard resistors to simulate the Skip Shift solenoid if you wish to defeat it on your automatic . * Some LS1/LT1 use a newer VATS system (PASSkeyIII) that the LIM will not bypass. Email with us with the donor vehicle information - Year and model. Features include: Microcontroller based VATS signal for reliability and accuracy All relay outputs fused with ATC type fuses All relay fuses have blown fuse indicator LED On board green blinking power LED indicator On board MIL (malfunction indicator LED) Optional sixth relay position ($10 extra) please specify if you need ground or 12v to activate. Optional tachometer signal divider/multiplier ($20 each) converts your LS1/LT1 tachometer signal for your stock Tachometer that was made for a 4,6,8 or 12 cylinder engine. Weight (1 LB) Small package (4.8in by 6.8in by 2.0in) 12 month warranty  The LIM also comes with a lot of instructions, pictures, diagrams and technical support.